Part Number: 193

Helps the engine breathe better taking the strain off the original breather box and stops oil being forced up to the airbox. (then 'seeping' over the carbs).
Includes screw in oil filler nozzle, stainless braided hose (colour may vary to shown), red 'K&N' breather filter, and 2 x hose finishers.
Now comes with choice of Black, Red or Blue finishers.
Fits all models '85-'07

Part Number: 64 T

For easier starting & smoother running.
Complete set of 4 Spark Plugs

Part Number: 159 M

NGK Spark Plugs
Original fitment and Grade
Set of 4 Spark Plugs

Beware of imitations from auction sites!! (give many problems)

Part Number: 148

'NGK' Spark Plug Caps (set of 4), in Black
note:If using original H.T. leads, will necessitate razoring the rubber boot above front barrels only for straighter H.T. lead routing.

Do your plug caps look like this? please see 'click on'

Part Number: 212

Fits all years: 1985-2007
4 x 'COP's and 4 x Wires with Silver resistors. Will work with 3-boost, Dyna 3k and digital speedos. With resistors to protect the aforementioned.

These will plug into the existing clips that are already on your stock coils. Quicker starts and cures hot starts. You can leave your old coils on your bike and just plug these right in their place. Clips and couplings are new.

Set has 2 x longer wires, these go in the front and will need to cross over to plug into their connectors (as original setup = left front wire goes to right front cylinder and vice versa).

IN-STOCK

Part Number: 19

Replacement air filter for original box. Add a few horses in one easy move. A must with the stage 1 Dynojet kit.

Part Number: 20

Gives a better mid-range power and response. A must when fitting 'race' exhausts.

Includes:
4 x Springs
4 x Needles
4 x E-Clips
4 x Washers
12 x Main jets (3 x different sizes)
4 x Pilot Air Jets

Part Number: 206 TC

Dynojet Stage 7 complete with Filters

Part Number: 206 TB

Dynojet Stage 7 Kit without Air Filters

Part Number: 206 TA

Part Number: 198 T

Big Radiator Kit, Available with Black or Silver Side Covers (Core Guards). Uses Stock Fan.
Diamension: 420mm x 325mm x 90mm, Thickness 25mm.
Radiation: 33kw (about 38,300 kcal/h), Material: Aluminium, Resistant: 196kpa, Weight: 1450 g
Admeasurement Condition:-
Velocity of Wind: 8 m/s
Water Flow: 40 litres/min
Result:- 80 inlet, 20 Outlet
Special Order Item
To Fit All Models

Available in:
A) Silver: £926.50 ($1,204.45) -- £1,111.80 Including VAT at 20%
B) Black: £969.00 ($1,259.70) -- £1,162.80 Including VAT at 20%
Note: Curved oil cooler available to suit, see #189T

Part Number: 102

Complete including cables, choke mechanism and new rubber inlet manifolds. Keep v-boost system. Simple to fit, pre-balanced, + more economical

For around an extra 15 BHP!!! (note: for filters please see our special filter kit 102A below).

For up-to-date price, please call or email.

Special Order Item

Part Number: 102 A

© Angled filter manifold kit (2 x 'Megaflow' big foam filters + 4 x angled silicone filter manifold adapters )
vastly (+30%) improves power over using 4x conical type filters!

Key to 'back to back' dyno test to show comparison (uncalibrated) © 2003

Blue - Flat slides with 'Megaflow' filter kit!
Red - Flat slides as supplied with open bell-mouths
Green - Flat slides with 4 'conical type' filters!

Part Number: 38

Converts the original diaphragm, to 6-coil springs.This is how the V-Max clutch should have been built.(note: would not/cannot be used with 60% stronger clutch spring no 38c).

A) Spring clutch conversion complete (no steel or friction plates): £175.00 -- £210.00 Including VAT at 20%
B) Heavy Duty Spring set only (6 set): £30.00 -- £36.00 Including VAT at 20%

Part Number: 38B

Performance clutch friction plates. Full set.

Part Number: 38E

Full set = 7 x

Part Number: 38F

Full set

Part Number: 38D

Part Number: 162T

Complete set of Clutch Friction plates

Part Number: 6

Complete set of Clutch Steel plates

Part Number: 38 C

This cures 90% of slipping clutches ( as strong as they should have been made originally). Best to replace friction plates as well! as they may be glazed. (note: would not/cannot , be used with Barnett Spring Conversion no 38).

Part Number: 133 T

Replacement silicone (carbon core) ignition leads. set of 4, pre-cut lengths, in:

(can be fitted with NGK Plug caps Ref 148)

Part Number: 150T

The Best proven Carburettor Balancer/gauge available.
Carbtune kit comes complete with nitrile hoses, 5mm and 6mm adapters to fit virtually any motorcycle, restricters, carry case, comprehensive instructions and warranty.

The 4-column Carbtune will work on twins, triples and four.
Great Investment, saves time and money. As accurate carburettor balance setting is really critical on a Vmax, stops backfiring on over run and smooth pick up on lift off.
Keep your bike 'on song'.

Part Number: 201

This is a 6 piece direct replacement silicone race specification coolant hose kit (as the 7th hose (filler neck breather to header bottle) is unseen). Great quality with ultra high burst rating and better heat dispersal make these an essential upgrade for any bike. Also great for custom show use.

Available in Blue, Yellow, Black, Orange, Green, Red, Purple all Gloss finish.

Part Number: 74E

Multi adjustable ignition curve/ rev limit settings, PC Re-mappable ignition timing (Software downloandable), sits in original position using original connectors.

Available for Models with single pick-up

Part Number: 202 E

Multi adjustable ignition curve/ rev limit settings, PC Re-mappable ignition timing (Software downloandable), sits in original position using original connectors.

Available for Models with twin pick-up

Part Number: 164T

100% cotton 'Fruit of the Loom' T-shirt, writing and bike are in white (not grey as pictured)

(for those of us that "Eat, Sleep, and Dream V-maxes", you may as well "wear it" !!)

Available in:
M = Chest 40" x 28" Long in Black
L = Chest 44" x 29" Long in Black